{{ name }}
Artikelnummer {{ combinedCodeWithHighlight }}
Klantartikelnummer:
EAN/GTIN:
Nummer fabrikant:
HiPer-Drill basiselement, 5×D, ⌀ DC: 25mm
Artikelnummer: 231610 25
Klantartikelnummer:
- Version: 5×D
- Shank: ISO 9766
- Use for drilling: limited cross-drilling; limited drilling through a stack; limited drilling with oblique exit; limited oblique spot drilling
- Number of cutting edges Z: 2
- Through-coolant: yes
Productdetails
Technische gegevens
| Series | HiPer-Drill | |
| Version | 5×D | |
| Shank | ISO 9766 | |
| Use for drilling | limited cross-drilling; limited drilling through a stack; limited drilling with oblique exit; limited oblique spot drilling | |
| Number of cutting edges Z | 2 | |
| Through-coolant | yes | |
| Dia. range Dc | 25 mm - 25.99 mm | |
| Reach L1 | 130 mm | |
| Shank ⌀ Ds | 32 mm | |
| Shank length Ls | 60 mm | |
| Clamping screw | 231999 15IP (5.0 Nm) | |
| Overall length L | 227 mm | |
| Type of product | Indexable drill |
Identificatienummers en classificaties
| Artikelnummer | 231610 25 | |
| EAN/GTIN | 4045197603081 | |
| Nummer fabrikant | 231610 25 |
Omschrijving
Version:
- Very high feed rates and maximum performance due to optimally matched geometries and materials.
- Precise positioning of the cutter insert due to Vee insert seating and secure clamping by the centre bore.
- High concentricity when assembled. (For holes up to IT9 accuracy)
- Shank support for optimum stability in operation.
Application:
For stationary and rotating use. For holes up to IT9 accuracy.
Note:
The insert screw must be replaced after every fifth change of cutter insert.
Further sizes up to ⌀ 50.99 mm available on request.
Clamp in a hydraulic chuck (such as No. 302026 size 20) for optimum radial run-out.
For optimum stability, clamp the drill so the overhang is as short as possible.
Further sizes up to ⌀ 50.99 mm available on request.
Clamp in a hydraulic chuck (such as No. 302026 size 20) for optimum radial run-out.
For optimum stability, clamp the drill so the overhang is as short as possible.
Downloads en documenten
Vergelijk met soortgelijke producten
Dit artikel |
Aanbevelingen |
||
|---|---|---|---|
HiPer-Drill basiselement, 5×D, ⌀ DC: 25mm
op aanvraag
Op voorraad
Leverbaar in 11-14werkdagen
16 stuks direct leverbaar
16 stuks leverbaar in 11-14werkdagen
€ 525,00
Excl. BTW
Excl. verzendkosten
|
|||
| Dia. range Dc | 25 mm - 25.99 mm | 25 mm - 35 mm | 25 mm - 35 mm |
| Number of cutting edges Z | 2 | 2 | 2 |
| Version | 5×D | 5×D | 5×D |
| Through-coolant | yes | ja | ja |
| Shank | ISO 9766 | ISO 9766 | Morsekona |
| Reach L1 | 130 mm | 187,3 mm | 187,3 mm |
| Type of product | Indexable drill | Vändskärsborrar | Vändskärsborrar |